2026 Cost

Paver Cost in Washington: $10–$58 / sq ft

15% above the national average · Free instant calculator below, no signup

Paver Cost: Washington 2026 Pricing

In Washington, paver costs are approximately 15% above the national average. Seattle metro has high labor costs; eastern WA is more affordable. Run the calculator below for a Washington-adjusted estimate.

Updated May 2026Reviewed by CostPerProject Editorial Team

Project Dimensions

Length (ft)

Width (ft)

Project Size

Paver Material

Pattern Complexity

Base Preparation

ZIP Code (optional)

Estimated Project Cost

Enter your project dimensions above to see your estimate.

Paver Cost in Washington: What to expect

Washington (WA) is in the West Coast region. Home improvement costs here are approximately 15% above the national average due to local labor rates, material availability, and regional demand.

Seattle metro has high labor costs; eastern WA is more affordable.

Average paver rates in Washington

Type	Washington	National Avg
Concrete Pavers	$10.35 – $25.30 / sq ft	$9.00 – $22.00 / sq ft
Brick Pavers	$13.80 – $32.20 / sq ft	$12.00 – $28.00 / sq ft
Natural Stone	$18.40 – $57.50 / sq ft	$16.00 – $50.00 / sq ft
Permeable Pavers	$17.25 – $40.25 / sq ft	$15.00 – $35.00 / sq ft

Paver Cost in major Washington cities

Costs do vary between metros and rural areas, but we only publish a figure we can source. Within-state variation is driven by local labor markets that do not track city size reliably, so we apply the Washington state rate across the cities below rather than estimating a premium we cannot verify. For a figure specific to your job, use the calculator above.

Seattle

$10.35 – $57.50 / sq ft

Washington state rate

Spokane

$10.35 – $57.50 / sq ft

Washington state rate

Tacoma

$10.35 – $57.50 / sq ft

Washington state rate

Why paver costs differ in Washington

The Washington multiplier reflects three things: prevailing wages for skilled trade labor, material delivery cost from regional suppliers, and any state or municipal permitting overhead. Compared to neighboring states, Washington sits 15% above the national average.

State	Cost vs national average
Washington (this page)	15% above the national average
Idaho	7% below the national average
Oregon	9% above the national average

Permits and timing in Washington

Permits in Washington

Washington cities require permits for roofing, paving, and structural exterior work. Tree removal is regulated in many municipalities, notably Seattle, where permits are required for trees over a certain diameter and protected heritage trees. Always check with your local urban forestry or building department.

Best time of year for paver in Washington

Spring through early fall when the ground isn't frozen; avoid extreme heat for installer comfort and proper polymeric sand setting.

Paver Cost FAQs for Washington

Common questions about paver cost, permits, and timing in Washington.

How much does paver cost in Washington?

Paver Cost in Washington typically costs $10.35–$57.5, which is 15% above the national average. Final pricing depends on paver material, pattern complexity, how much base preparation the site needs, and access.

Does paver cost more in Seattle?

Not by a figure we can source. Quotes in Seattle generally track the Washington rate shown here. Within-state differences are driven by local labor markets rather than by city size, so we do not publish a separate Seattle premium. Getting two or three local quotes is the reliable way to see where your job lands.

Do I need a permit for paver installation in Washington?

When is the best time of year for paver in Washington?

Spring through early fall when the ground isn't frozen; avoid extreme heat for installer comfort and proper polymeric sand setting.

How do paver costs in Washington compare to neighboring states?

Washington sits 15% above the national average for paver. Compared to neighboring states: Idaho runs about 22% lower, Oregon runs about 6% lower.

Why is paver more expensive in Washington?

Seattle metro has high labor costs; eastern WA is more affordable. Combined with regional labor rates and material logistics, Washington sits 15% above the national average for paver.